|1974 L-82 Stingray Corvette,
VIN # 1737T4S404070
400 CID Engine, bored .30 over
500+ Horse Power
5-speed Tremex TKO-600 .64 5th gear
18,793 current mileage
I do have the original numbers matching 350 4 bolt main block that goes with the
car as well if you would like to have it.
Clear Texas Title!!!!!!
First and foremostThis is not a rust bucket. I purchased it 10 years ago out of
Arizona and started building it up to where it is today. The car has been garage
kept every since and not driven in the rain. Solid, sound frame, no rust.
Front Sway barpoly bushing.
VBP-Vett Brake Products 550lb front coil springs
VBPHeavy Duty Tie rod sleeves
All front end bushing, idler arm, U-joints, tie rods, everything replaced.
Lower A-frame bushings are Poly.
New brake calipers and pads.
Original Numbers matching housing: Posi rear end
Heavy Duty reinforced rear mounting cover
Auburn Pro Series carrier: Read about it here:
4:11 Richmond gearing and pinion set
Heavy Duty Custom machined Chrome Molly steel---side yolks and shaft retainers.
NEW Heavy duty C-Channel trailing arms with heavy duty high performance bearings.
Custom machined Chrome Molly steel ---Spindlesincludes new emergency brake
assembly, pads, etc
Carbon Fiber Leaf spring 360lb, Poly busing on connecting studs.
Adjustable Rear Strut Rods with poly bushings.
Rear Sway Bar---solid 7/8 with Poly bushings.
Heavy duty U-joints in drive shaft and independent suspension side shafts, all 3
shafts have been balanced.
UNDER THE HOOD:
400 CID engine bored .30 over
Gear drive Timingno chain
11 to 1 compression forged aluminum pistons
Solid Roller Tappet Cam, 600 lift 300 duration
Roller Rocker quick change Crane lifters
(You do not need to remove the intake to change the cam in the car if so desired.)
Roller rocker arms with Stud girdle.
Edelbrock Aluminum water pump.
March under drive Pulley system.
MSD billet Distributor MSD # 8572.
MSD 6AL ignition with a 7,000 rpm chip plugged into it.
MSD 8.5mm wires.
Dart II Aluminum Heads 230 180.
Hooker Competition Plus Ceramic coated headers 1 primary tubes 3 outlet
2.5 exhaust all the way back to the flow masters, with polished stainless steel tips.
Fast EZ EFI Multi port fuel injection system, # 3012350-05E with 36lb injectors,
high flow fuel pump, 02 sensor, fuel regulator, Computer controlled. etc,
Read about it here:
To keep it all cool ----Aluminum dual rowBe Cool radiator with dual 11in electric fans 185 temp control
Read about it here:
COLD AIR CONDITIONING:
Vintage Air Complete Gen IV kit for 1968-76 Corvette
A/C system with polished compressor, ceramic coated mounting brackets, no
expense spareduses factory A/C interior Controls, new control module from
Read about it here:
Lots of Chrome---hinges, Master Cylinder, Valve Covers, etcunder the hood.
Has less than 2000 miles on it.
Tremec TKO-600 5 speed with .64 5th gearread about it here
New Bell housing, New Flywheel, Center Force Dual fraction clutch and pressure
Original Color--Med Saddle Leather
Tilt telescopic steering wheel. It all professionally rebuilt.
Horn works fine.
All newEntire Dash, all sections, Console, headliner rails, side windshield
runners, Emergency brake housing, door panels, seat covers and seat foam,
T-Top under pads, Seat backs, new carpet front and rear with new 3 door
compartment in back.
All original colors and carpet configurations.
IROC heat and sound installation on entire floorboard front and rear under carpet.
All gauges work except the clock.
Speedo is accurate to two (2) miles per hour. Tach works great, no issues.
New A/C controller unit.
Kenwood stereo, Pioneer power amp, 6 speaker system.
New Instrument cluster/ radio bezel
Custom compression dual 6X9 speaker box in rear area. Matched to carpet color.
Seat Belts are original.
WHEELS & TIRES:
15 x 8.5 front mag
15 x 10.5 rear mag
Front tiresP225/60 15 BFG Radial T/As
Rear Tires P275/60 15 BFG Radial T/As
GM-Admiral Metallic Blue
The paint on the car the looks great. There are minor chips or scratches associated
with a 10 year old paint job.
To a perfectionist and to be show room winning ready I would personally paint it again.
I have over $50k invested in the car as it sits.
Serious inquires only.
I run pump gas, 93 octane in the car and it runs great on it.
If payment is in any method other than cash, Cahiers check, bank check, etc.. it
will need to be verified with my bank before release of the vehicle.
For international sale the payment must clear my bank before the vehicle will be
allowed to be shipped internationally.
I will help with shipping arrangment in any manner what so ever to move vehicle
to transport location in San Antonio, Texas, USA if you wish.
Give me a call with any questions.
Mileage: 18,793 miles
Price: US $30,000.00
eBay Item number: 281006703746